White Rodgers 1F87-361 Installationshandbuch PDF herunterladen (Seite 7)

NOTE

Ifyouareprogrammingyourthermostatforthersttimeand

youwantprogrammingforalldaysoftheweektobethesame

asMonday’sprogram,pressRUNorHOLDatthispoint,and

proceedtoEnter Cooling Program.(ThissimpliedCOPYDAY

featureonlyworksthersttimeyouprogramyourthermostat.

Ifyouwanttocopyoneday’sprogrammingtoaspecicday

programming,refertoCOPY DAY FUNCTIONinOPERATING

FEATURES.Ifyouarechangingyourthermostat’sprogramming,

youmustprogrameachdayseparately.)

8. PressHOLDonce.“TU”(indicatingTuesdayprogram)willap-

pearinthedisplay,alongwiththestarttimeforthe1stheating

periodandthecurrentlyprogrammedtemperature.

9. Repeat steps 3 through 7 to completeTuesday’s heating

programming.

10.Continueenteringeachday’sprogramminguntilallheating

periodstimeandtemperatureshavebeenentered.

11.Whenyouhavecompletedenteringyourheatingprogram,

pressRUN.

Enter Cooling Program

If the outside temperature is below 50°F, disconnect power

to the cooling system before programming. Energizing

the air conditioner compressor during cold weather may

cause personal injury or property damage.

▲

CAUTION

Reset Operation

Ifavoltagespikeorstaticdischargeblanksoutthedisplayor

causeserraticthermostatoperationyoucanresetthethermo-

stat by pressing

, andTIME at the same time.This

alsoresetsthefactorydefaultstothecongurationmenuand

TROUBLESHOOTING

program.Ifthethermostathaspower,hasbeenresetandstill

doesnotfunctioncorrectlycontactyourheating/coolingservice

personorplaceofpurchase.

Batteries

Foroptimumperformance,werecommendreplacingbatteries

onceayearwithfresh“AA”Energizer

alkalinebatteries.

1. MoveSYSTEMswitchtoCOOLposition.

2. Follow the procedure for entering your cooling program,

usingyourselectedcoolingtimesandtemperatures.

CHECK YOUR PROGRAMMING

Followthesestepstocheckyourthermostatprogrammingone

naltimebeforebeginningthermostatoperation.

1. MoveSYSTEMswitchtoHEATposition.

2. PressPRGMtoviewthe1stMondayheatingperiodtimeand

temperature.EachtimeyoupressPRGM,thenextheating

periodtimeandtemperaturewillbedisplayedinsequence

forMonday.PressHOLDtodisplayTuesday’s1stheating

period, and press PRGM to view each of the remaining

Tuesday’s heating period timeand temperatures.To view

eachday’sheatingprogram,pressHOLDtochangedayand

thempressPRGMtolookateachprogrammingperiodfor

theday.(Youmaychangeanytimeortemperatureduring

thisprocedure.)

3. PressRUN.

4. MoveSYSTEMswitchtoCOOLposition.

5. Repeatstep2tocheckcoolingprogram.

6. MoveSYSTEMswitchtoHEATorCOOLandpressRUNto

beginprogramoperation.

YOUR THERMOSTAT IS NOW COMPLETELY PROGRAMMED AND

READY TO PROVIDE MAXIMUM COMFORT AND EFFICIENCY!

OPERATION

Symptom Possible Cause Corrective Action

No Heat/No Cool/No Fan

(common problems)

Blownfuseortrippedcircuitbreaker.1.

FurnacepowerswitchtoOFF.2.

Furnaceblowercompartmentdoororpanel3.

looseornotproperlyinstalled.

Replacefuseorresetbreaker.

TurnswitchtoON.

Replacedoorpanelinproperpositiontoengage

safetyinterlockordoorswitch.

No Heat

Pilotlightnotlit.1.

SYSTEMSwitchnotsetto2. HEAT.

Looseconnectiontothermostatorsystem.3.

FurnaceLock-OutCondition.Heatmayalso4.

beintermittent.



HeatingSystemrequiresserviceor5.

thermostatrequiresreplacement.

Re-lightpilot.

SetSYSTEMSwitchtoHeat andraisesetpointabove

roomtemperature.

Verifythermostatandsystemwiresaresecurelyat-

tached.

Manyfurnaceshavesafetydevicesthatshutthesys-

temdownwhenalock-outconditionoccurs.Iftheheat

worksintermittentlycontactthefurnacemanufactureror

localservicepersonforassistance.

Diagnostic:SetSYSTEMSwitchtoHEATandraise

thesetpointaboveroomtemperature.Within afew

secondsthethermostatshouldmakeasoftclick

sound.Thissoundusuallyindicatesthethermostat

isoperatingproperly.Ifthethermostatdoesnotclick,

trytheresetoperationlistedabove.Ifthethermostat

doesnotclickafterbeingresetcontactyourheating

andcoolingservicepersonorplaceofpurchasefor

areplacement.Ifthethermostatclicks,contactthe

furnacemanufactureroraservicepersontoverifythe

heatingsystemisoperatingcorrectly.

1 2 3 4 5 6 7 8

Kommentare zu diesen Handbüchern

Keine Kommentare

White Rodgers 1F87-361 Installationshandbuch Seite 7

Kommentare zu diesen Handbüchern