White Rodgers 1F87-361 Installationshandbuch PDF herunterladen (Seite 2)

Mounting

holes

Mounting

holes

Electric/Gas

switch

Screw anchors

INSTALLATION

REMOVE OLD THERMOSTAT

1. Shutoffelectricityatthemainfuseboxuntilinstallationis

complete.Ensurethatelectricalpowerisdisconnected.

2. Removethefrontcoveroftheoldthermostat.With wires

still attached, removewallplate fromthe wall. If the old

thermostathasawallmountingplate,removethethermostat

andthewallmountingplateasanassembly.

3. Identify each wire attached to the old thermostat using

the labels enclosed with the new thermostat.

4. Disconnectthewiresfromoldthermostatoneatatime.DO

NOT LET WIRES FALL BACK INTO THE WALL.

5. Installnewthermostatusingthefollowingprocedures.

ATTENTION!

Thisproductdoesnotcontainmercury.However,thisproduct

mayreplaceaunitwhichcontainsmercury.

Donotopenmercurycells.Ifacellbecomesdamaged,donot

touchanyspilledmercury.Wearingnonabsorbentgloves,take

upthespilledmercurywithsandorotherabsorbentmaterialand

placeintoacontainerwhichcanbesealed.Ifacellbecomes

damaged,theunitshouldbediscarded.

Mercurymustnotbediscardedinhouseholdtrash.Whenthe

unitthisproductisreplacingistobediscarded,placeinasuit-

ablecontainer.Refertowww.white-rodgers.comforlocationto

sendproductcontainingmercury.

ELECTRIC HEAT OR SINGLE-STAGE

HEAT PUMP SYSTEMS

Thisthermostatisconguredfromthefactorytooperateaheat/

cool,fossilfuel(gas,oil,etc.),forcedairsystem.Itiscongured

correctlyforanysystemthatDOESNOTrequirethethermostat

toenergizethefanonacallforheat.Ifyoursystemisanelectric

heatorheat-pumpsystemthatREQUIRESthethermostatto

turnonthefanonacallforheat,locatetheELECTRIC/GAS

switch onthebackof the thermostat(seeg.1)andswitch

it to the ELECTRIC position. This will allow the thermostat

toenergizethe fanimmediately on a callforheat.Ifyouare

unsureiftheheating/coolingsystemrequiresthethermostatto

controlthefan,contactaqualiedheatingandairconditioning

serviceperson.

ATTACH THERMOSTAT BASE TO WALL

1. Removethepackingmaterialfromthethermostat.Gently

pullthecoverstraightoffthebase.Forcingorpryingonthe

thermostatwillcausedamagetotheunit.Ifnecessary,move

theelectricheatswitch(seeELECTRIC HEAT SYSTEMS,

above).

2. Connectwiresbeneathterminalscrewsonbaseusingap-

propriatewiringschematic(seegs.2through7).

3. Placebaseoverholeinwallandmarkmountingholeloca-

tionsonwallusingbaseasatemplate.

4. Movebaseoutoftheway.Drillmountingholes.

5. Fastenbaselooselytowall,asshowning.1,usingtwo

mounting screws. Place a level against bottom of base,

adjustuntillevel,andthentightenscrews.(Levelingisfor

appearanceonlyandwillnotaffectthermostatoperation.)

Ifyouareusingexistingmountingholes,orifholesdrilled

aretoolargeanddonotallowyoutotightenbasesnugly,

useplasticscrewanchorstosecuresubbase.

6. Pushexcesswireintowallandplugholewithare-resistant

material(suchasberglassinsulation)topreventdraftsfrom

affectingthermostatoperation.

BATTERY LOCATION

2“AA”alkalinebatteriesareincludedinthethermostatatthe

factorywithabatterytagtopreventpowerdrainage.You must

remove the battery tag to engage the batteries.

If“BATT”or“CHANGE ”isdisplayed,thebatteriesare

lowandshouldbereplacedwithfresh“AA”Energizer

alkaline

batteries.Toreplacebatteries,installthebatteriesalongthetop

ofthebase(seeFig.1).Thebatteriesmustbeinstalledwiththe

positive(+)endtotheleft.

HYDRONIC (HOT WATER OR STEAM)

HEATING SYSTEMS

Thisthermostatissettooperateproperlywithaforced-airheat-

ingsystem.Ifyouhaveahydronicheatingsystem(asystem

thatheatswithhotwaterorsteam),youmustsetthethermostat

tooperateproperlywithyoursystem.Changethesecondop-

tioninthecongurationmenutoSL(seeCONFIGURATION

MENU,page4).

CHECK THERMOSTAT OPERATION

If at any time during testing your system does not operate

properly,contactaqualiedserviceperson.

Turnonpowertothesystem.

Fan Operation

Ifyoursystemdoes nothaveaGterminalconnection,skipto

Heating System.

1. MoveFANswitchtoON position.Theblowershouldbegin

tooperate.

2. Move FAN switch to AUTO position. The blower should

stopimmediately.

Figure 1. Thermostat Base

1 2 3 4 5 6 7 8

Kommentare zu diesen Handbüchern

Keine Kommentare

White Rodgers 1F87-361 Installationshandbuch Seite 2

Kommentare zu diesen Handbüchern